Steel Epoxy Stick - S1010

Price for 1 unit: £9.65
Ex. VAT: £8.04
Product Datasheet:
Download PDF

Not sure this is the right adhesive for your requirements?

Please contact our friendly team for some free advice about your individual requirements.

Product Overview

Steel Epoxy Putty Stick, S1010, is a hand-kneadable, non-rusting, steel-reinforced epoxy putty that mixes in one minute to provide fast, permanent repairs to items made of ferrous and aluminium metals.

This putty steel stick comes in a handy rod form with the curing agent encapsulated in the contrasting colour base material. Its putty-like consistency eliminates drips and runs, providing “no mess” application with no tools required to use.


This putty is black in colour after use.

Application uses

After proper mixing, S1010 moulds like clay and may be used in many industrial and home maintenance applications, including:

  • Repair of iron pipes
  • Tanks
  • Tools and equipment
  • Repair blow holes
  • Holding and placement of fixtures and signs
  • Repairs to moulds
  • Patterns and castings
  • Making prototypes
  • Thread locking
  • Repair cracked castings
  • Repairs to down spouts and gutters
  • Light fixture installations
  • Repairs to duct-work
  • Anchor bolts
  • As well as countless other uses

Remain stable for years

The unused portion of S1010 will remain stable for years if protected from direct contact with the air, in cool conditions.

Technical data

Resin Hydrocarbons, ketones, esters, halocarbons, alcohols, aqueous salt solutions and dilute acids and bases.
Electrical Resistance 30,000 mega Ohms Dielectric
Strength (Steel) 300 Volts/mil
Shrinkage <1%
Non-volatile content 100%
Shelf life >6 months @ 25°C

Directions for Use


Twist or cut off required amount. To mix, knead with fingers to a uniformed colour. If mixing is difficult, warm to room temperature or slightly above. Apply to the surface to be repaired (within 2 minutes of mixing). The mixed epoxy does not exhibit high bond strength at this point, but appears to be merely lying on the surface. Force into any cracks or holes to be filled and strike off excess material, preferably with a tool wetted with clean water. When applying to a damp, wet or slowly leaking area, Work the material forcefully into the surface and apply pressure until adhesion begins to take effect.

For a smooth appearance of the cured compound, hand rub with water or a damp cloth prior to hardening.


Remove excess material before hardening begins. After 15-20 minutes, the epoxy will harden like metal and start to form a tenacious bond. After just 45 minutes, it is completely cured and can be drilled, sawed, carved, sanded, stained or painted.

In order to achieve optimum adhesion, surface should be cleaned free of grease or dirt. Scuffing or sanding the surface prior to cleaning helps to ensure a good bond.

Cure Performance

Initial cure 1 hour max
Full cure time 24 hours
Lap shear strength (steel) 6.2 N/mm2
Shore D hardness 80
Compressive strength 84 N/mm2


Opening time 3.5 minutes
Max. temperature resistance 120°C continuous | 150°C intermittent


IRRITANT: Contains epoxy resin and may cause skin irritation in sensitive individuals. Unnecessary skin contact should therefore be avoided. If skin contact occurs, wash with a proprietary hand cleaner, followed by washing with soap and water. In case of eye contact, flush with clean water for at least 15 minutes, then seek medical attention. When fully cured, the product can be considered non-toxic. Store in cool conditions, preferably away from direct sunlight or excessive heat. Shelf life at least 6 months @ 25°C.

Steel Epoxy Stick adhesive price

If you buy this adhesive putty in bulk it can cost from only £7.71 / stick.

Not sure if this steel putty is right for your requirements?

If you are not sure if this adhesive is correct for your requirements please contact us to discuss your requirements and we can point you in the right direction.


01143951004 01152000565 01214616076 01332482732 02477350519