Steel Epoxy Stick – S1010

£10.50

Steel Epoxy Putty Stick, S1010, is a hand-kneadable, non-rusting, steel-reinforced epoxy putty that mixes in one minute to provide fast, permanent repairs to items made of ferrous and aluminium metals. Our sticks are great value as they are approximately 130g, 175mm long and 22mm diameter which is larger than most on the market.

Product Datasheet: Download PDF

23 in stock

1 - 2 0%
3 - 5 5%
6 + 10%

Description

Steel Epoxy Putty Stick, S1010, is a hand-kneadable, non-rusting, steel-reinforced epoxy putty that mixes in one minute to provide fast, permanent repairs to items made of ferrous and aluminium metals. Our sticks are great value as they are approximately 130g, 175mm long and 22mm diameter which is larger than most on the market.

This putty steel stick comes in a handy rod form with the curing agent encapsulated in the contrasting colour base material. Its putty-like consistency eliminates drips and runs, providing “no mess” application with no tools required to use.

Colour

This putty is black in colour after use.

Application uses

After proper mixing, S1010 moulds like clay and may be used in many industrial and home maintenance applications, including:

  • Repair of iron pipes
  • Tanks
  • Tools and equipment
  • Repair blow holes
  • Holding and placement of fixtures and signs
  • Repairs to moulds
  • Patterns and castings
  • Making prototypes
  • Thread locking
  • Repair cracked castings
  • Repairs to down spouts and gutters
  • Light fixture installations
  • Repairs to duct-work
  • Anchor bolts
  • As well as countless other uses

Remain stable for years

The unused portion of S1010 will remain stable for years if protected from direct contact with the air, in cool conditions.

Technical data

ResinEpoxide
Resistant toHydrocarbons, ketones, esters, halocarbons, alcohols, aqueous salt solutions and dilute acids and bases.
Electrical Resistance30,000 mega Ohms Dielectric
Strength (Steel)300 Volts/mil
Shrinkage<1%
Non-volatile content100%
Shelf life>6 months @ 25°C

Directions for Use

Mixing

Twist or cut off required amount. To mix, knead with fingers to a uniformed colour. If mixing is difficult, warm to room temperature or slightly above. Apply to the surface to be repaired (within 2 minutes of mixing). The mixed epoxy does not exhibit high bond strength at this point, but appears to be merely lying on the surface. Force into any cracks or holes to be filled and strike off excess material, preferably with a tool wetted with clean water. When applying to a damp, wet or slowly leaking area, Work the material forcefully into the surface and apply pressure until adhesion begins to take effect.

For a smooth appearance of the cured compound, hand rub with water or a damp cloth prior to hardening.

Hardening

Remove excess material before hardening begins. After 15-20 minutes, the epoxy will harden like metal and start to form a tenacious bond. After just 45 minutes, it is completely cured and can be drilled, sawed, carved, sanded, stained or painted.

In order to achieve optimum adhesion, surface should be cleaned free of grease or dirt. Scuffing or sanding the surface prior to cleaning helps to ensure a good bond.

Cure Performance

Initial cure1 hour max
Full cure time24 hours
Lap shear strength (steel)6.2 N/mm2
Shore D hardness80
Compressive strength84 N/mm2– 12,000 psi

Properties

Opening time3.5 minutes
Max. temperature resistance120°C continuous | 150°C intermittent

Precaution

IRRITANT: Contains epoxy resin and may cause skin irritation in sensitive individuals. Unnecessary skin contact should therefore be avoided. If skin contact occurs, wash with a proprietary hand cleaner, followed by washing with soap and water. In case of eye contact, flush with clean water for at least 15 minutes, then seek medical attention. When fully cured, the product can be considered non-toxic. Store in cool conditions, preferably away from direct sunlight or excessive heat. Shelf life at least 6 months @ 25°C.

Steel Epoxy Stick adhesive price

If you buy this adhesive putty in bulk we offer a discounted rate making it even better value for money.

Not sure if this steel putty is right for your requirements?

If you are not sure if this adhesive is correct for your requirements please contact us to discuss your requirements and we can point you in the right direction.

Additional information

Weight0.16 kg
Brand

Bondrite

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

You may also like…